Two tubes, reusable cuff for non-invasive blood pressure measurement.
Size: 25 - 35 cm in circumference. Adult human patient.
Suitable for human and animal patient.
Warranty: 3 months.
This bracelet is suitable for different brands of blood pressure monitors.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

One-way reusable cuff for non-invasive blood pressure measurement.
Size: 20,5 to 28 cm of arm circumference.
With hose connector included.
For small adult.
Suitable for human and animal patient.

This cuff is suitable for different brands of equipment and different equipment (patient monitors, defibrillators, blood pressure monitors). What must be taken into account is the connector at the end of the hose, which must be the same in order to connect to the equipment. If the connector is not the same, then you can save the connector on the cuff you will be replacing and use it to replace the connector on the cuff that will deliver with your purchase.



The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

One-way resusable cuff for non-invasive blood pressure measurement.
Size: 18 to 26 cm arm circumference.
With hose connector included.
For a small pediatric patient.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

One-way resusable cuff for non-invasive blood pressure measurement.
Size: 18 to 26 cm arm circumference.
With hose connector included.
For a small pediatric patient.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

One-way reusable handle/ cuff for non-invasive blood pressure measurement.
Size: 23 to 33 cm in circumference.
With hose connector included
For adult patient

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

One-way cuff, with hose connector included, reusable, for non-invasive blood pressure measurement.

Size: 10 to 19 cm in circumference. Neonatal patient.
Suitable for human and animal patient.
Warranty: 3 months.

This bracelet is suitable for different brands of equipment and different equipment (multiparameter monitors, defibrillators, blood pressure monitors). What you have to take into account is the connevtor that is at the end of the hose, which must be the same to be able to connect to the equipment. If the connector is not the same, then you can save the connector from the cuff it will replace the connector on the cuff that came with your purchase.

Synonymous names: Armband/ Cuff/ Chambers for non-invasive pressure

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Disposable accessory, which prevents moisture from entering the equipment and connects the patient circuit line to the monitoring system. It can be reused as long as it is disinfected. It is implemented in adult and pediatric patients in a Feas Electrónica multiparameter monitor, under the supervision of trained health care staff.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Neonatal oximeter sensor DB9M/G Feas Electronica 3026.

This sensor is used in oximetry monitoring systems to non-invasively determine Percent Oxygen Saturation (SpO2), pulse rate, and pulse plethysmographic waves.
Its use is indicated for patients of less than 3kg.

It has a length of 40 cm.
Protection against liquids IPX1.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Nellcor Doc-10 SpO2 Extension Cable

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Multifunction pedal, consisting of three silicone rubber buttons for the Micromotor Fisiodispenser for dental implantology with which the pump, the direction of rotation and the passage through the different functions can be manipulated.
· Hands-free equipment to control and manage programs.
· Heavy multi-function pedal for good stability.
· Main control: controls the motor in progressive (linear) mode or can be programmed to operate in on / off mode.
· Function: Pressing it once toggles from one function to another. Holding it down, navigates between the three programs for each function.
· Direction of rotation: The micro motor has the possibility of reversing its rotation using the DIRECT / REVERSE button on the keyboard, or the "Direction of rotation" button on the pedal. The REVERSE direction is indicated on the display and by an audible tone.
· Pump: by pressing once, it will turn on and off. By keeping the last selected stream. Holding tight increases the flow: off, on 25%, on 50%, on 75%, on 100%, off. This is represented on the screen by 1, 2, 3 or 4 drops.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

PRODUCT DESCRIPTION

Rolling unit ideal for use in clinics, sanatoriums, hospitals and health centers in general. Allows organized storage of supplies and placement of equipment on the top shelf
Multipurpose trolley.
Top shelf with protective railing and transparent cover.
Sliding ABS drawer, with internal compartments that allow efficient organization of supplies.
ABS middle shelf.
Bottom shelf made of ABS.
Material: ABS, high impact engineering plastic.
2 garbage cans with lid
4 silent wheels of 13 cm, 2 of them with brakes.
Warranty: 1 year.
Aluminum structure covered with ABS plastic, material resistant to rust and corrosion.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Iron structure, which allows to maintain and move the preamplifier of hemodynamic studies through the procedure table. Use in Feas Electronica brand hemodynamic and electrophysiology polygraphs exclusively.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

RENT
Include equipment rental. For different rental periods, please consult

Syringe infusion pump model SN-50F66 is a constant volume, channel and speed controlled infusion pump. It is characterized by high precision, stable flow rate and low dosage.

It is used particularly for the infusion of sodium nitroprusside, dopamine, propofol and antibiotics for acute and serious illnesses. The pump has multiple types of alarm functions to ensure a safe and reliable infusion process.

This product is used to clinically control the flow and velocity of fluids (drugs, nutrients, and blood) infused into the patient's body for safer use.

GENERAL CHARACTERISTICS
* The equipment can store customized syringe information from 33 different manufacturers, Weigao and 32 other manufacturers, configurable by the user.
* SN-50 pumps can use sterile and disposable syringes of 5ml, 10ml, 20ml, 30ml or 50ml, depending on the model. Automatically recognizes the syringe placed.
* The equipment can store up to 2000 historical infusion records, which include the following information: injection mode, injection speed, alarm information, total injected volume, threshold value of the occlusion pressure limit of the path, limiting quantity, number of syringe and information of the operation.
* It has the following alarm functions:
Incorrect position of the syringe.
Of residual limit.
Occlusion
End of injection.
Without operation
Empty syringe
Flow limit exceeded.
Plunger decoupled.
Power cable disconnected.
Of discharged battery.
Battery exhausted.
Of system error.
* Operating time of the battery: starting from a full charge, the battery can support 6 hours of operation in a channel at a speed of 5 ml/h and 4 hours of operation in two channels.
* Allows battery operation and charging from the car's 12Vdc connector.

TECHNICAL SPECIFICATIONS
* Dimensions:
354mm x 195mm x 148mm (Length x Width x Height)
* Weight: 3.45kg (includes support).
* Electrical feeding:
AC input: 100V ~ to 240V ~, 50/60 Hz.
DC input: 12Vdc.
Battery voltage: 12Vdc.
Nominal power: 40 VA.

CERTIFICATES
* Quality Standards:
ISO13485
Disp. A.N.M.A.T. 3266/2013: B.P.F
Disp. A.N.M.A.T. 2319/02; certified
* Safety Standards:
UNE-EN 60601-1 (Eq IRAM 4220-1 and IEC 601-1), Class I - Prot. Desc. Elect .: CF,
UNE-EN 60601-1-2 (Electromagnetic Compatibility).
Authorized by the A.N.M.A.T .: PM 1125-18.

ACCESSORIES
● 1 Power cable.
● 1 User's manual.
● 1 Content list.
● 1 Manufacturing quality certificate.
● 1 Warranty card.
The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

GENERAL CHARACTERISTICS
* It is characterized by its high precision, stable flow rate and low dosage. It is particularly used for the infusion of sodium nitroprusside, dopamine, propofol and antibiotics for acute and severe diseases.
* The equipment can store personalized syringe information from 33 different manufacturers, Weigao and 32 other manufacturers, configurable by the user.
* The SN-50F66 pump can use sterile and disposable syringes of 5ml, 10ml, 20ml, 30ml or 50ml. It Automatically recognices the placed syringe.
* The equipment can store up to 2000 historical infusion records, which include the following information: injection mode, injection rate, alarm information, total volume injected, threshold value of the line of occlusion pressure limit, limiting quantity, number of syringe and operation information.
* It has the following alarm functions:
Incorrect position of the syringe.
Residual Limit
Occlusion
End of injection.
No operation
Empty syringe.
Flow limit exceeded.
Plunger decoupled.
Power cord disconnected.
Battery discharged.
Battery exhausted
System error
* Battery operating time: starting from a full charge, the battery can withstand 5 hours of operation at a speed of 5 ml / h on two channels.
* Allows operation and battery charging from the 12V connector of the car.

TECHNICAL SPECIFICATIONS
Dimensions: (Length x Width x Height)
3-channel pump: 469mm x 277mm x 207mm
Weight:
3-channel pump: 5.4kg (includes support).
Feeding:
AC input: 100V ～ to 240V ～, 50/60 Hz.
DC input: 12Vdc
Battery voltage: 12Vdc
Nominal power: 40 VA.
Quality Standards: ISO13485, Disp. A.N.M.A.T. 3266/2013: B.P.F. and Disp. A.N.M.A.T. 2319/02; certified.
Safety Standards: UNE-EN 60601-1. (Eq. IRAM 4220-1 and IEC 601-1), Class I - Prot. Desc. Elect .: CF, UNE-EN 60601-1-2 (Electromagnetic Compatibility).
Authorized by A.N.M.A.T .: PM 1125-18.

ACCESSORIES
● 1 Power cable.
● 1 User manual.
● 1 List of content.
● 1 Certificate of manufacturing quality.
● 1 Warranty card.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Includes equipment rental. For different rental periods, please consult.

Infusion pump of volumetric type with peristaltic perfusion system that accepts universal type set. Comprehensive and effective solution to optimize infusion therapy in all the units of the Hospitals and Health Centers.

• Great quality. Easy to use. Menu in English.
• It has a simple system to calibrate different sets of infusion and can be recorded up to 12 calibrations for different sets.
• It has a vertical structure with an effective prevention against the entry of liquids. It can be hung from the serum support or placed on a table or car.
• High accuracy, due to an intelligent pulsating compensation made by a double micro-processed unit, resulting in a constant flow of high precision infusion.
• It has six types of infusion mode: Speed mode, Drip mode, Body Weight mode, Time mod, Infusion Plan and Drug Library or Drug Mode.
• Contains drip sensor.
• Contains ultrasonic bubble sensor, high sensitivity.
• It contains a pressure sensor that allows adjustment of 10 levels of occlusion pressure.
• High definition screen, allows the on-screen display of the controlled / running function.
• Illuminated alarm panel (up to 12 alarms). Interface for nurse call.
• Record of 1500 historical events.

The following features and functions contribute to make the patient's treatment more pleasant:
• When the pump door is opened, in a dark environment, a light is switched on automatically that allows changing the set or working on the infusion pump without turning on the ambient light.
• Silent operation and without vibrations, because it is equipped with a high quality motor.
• External DC power supply input, also works with 12Vdc input.
• Easy to transport due to its small size and weight.
• Interface USB.

TECHNICAL SPECIFICATIONS
Specification of IV set: 20 drops/ml or 60 drops/ml.

Infusion flow rate:
• Set IV of 20 drops/ml: 0.1ml/h ~ 1500ml/h.
• Set IV of 60 drops/ml: 0.1ml/h ~ 1500ml/h.
• When the speed is between 1ml/h ~ 99.9ml/h, the infusion flow rate is changed from 0.1ml/h.
• When the speed is above 100ml/h, the infusion flow rate is changed from 1ml/h.
• Accuracy: ± 5%.

Bubble Detector:
Ultrasonic detection method: bubbles are detected above 25μl.

Occlusion pressure value:
• Ten adjustable levels, with an error of ± 50mmHg or ± 25% (6.6KPa).
• Adjustment range: from 100mmHg (13.3KPa) to 900mmHg (120KPa).
Flow rate of the Purge Bolus:
• Adjustable between 5ml/h ~ 1000ml/h.
Kvo rate (to maintain permeable route):
• Adjustable minimum flow between 1ml/h ~ 5ml/h.

Built-in battery:
• Ni-Mh, 12 Vdc, 2300 mAh, the recharge cycle can be repeated up to 500 times.
• Operating time of the battery: with the battery fully charged, it can run continuously for more than 6 hours at a speed of 5ml/h.

Operation mode: Continuous.

Protection against the ingress of liquids: IP32.

Historical records:
You can store the historical records of more than 1500 infusions made.

Communication link: SN-1800V: RS-232.

• Supply voltage: 100V ~ to 240V ~ / 50Hz or 60Hz or 12Vdc external.
• Maximum power: 28 VA.
• Classification: class I and internally powered.
• Protection against electric shocks: Type CF.

Work environment:
• Operating conditions:
Ambient temperature: + 5ºC to + 40ºC.
Relative humidity: 20% to 90%.
Atmospheric pressure: 645mmHg (86kPa) to 795mmHg (106kPa).
• Storage conditions:
Ambient temperature: -20ºC to + 55ºC.
Relative humidity: 0% to 95%.
Environmental pressure: 375mmHg (50kPa) to 795mmHg (106kPa).

Weight: 1,8Kg.

Dimensions: 129mm x 130mm x 215mm (Width x Length x Height).

ACCESSORIES INCLUDED
1 Power cable to line.
1 user manual.

CERTIFICATES
• Certified Quality Standard:
ISO 13485.
Disp. A.N.M.A.T. 3266/2013: B.P.F.
Disp. A.N.M.A.T. 2319/02.
• Safety Standard:
IEC 60601-1 (Eq IRAM 4220-1 and IEC 601-1- Req.
IEC 60601-1-2 (Electromagnetic Compatibility).
IEC 60601-2-24 (Infusion Pumps).

FREQUENT QUESTIONS
Do you use any brand of infusion set?
Yes, the pump is not dependent on any brand of supplies. It is recommended that a silicone IV Set be used.

Can it be used in animals?
Yes, it can be used in animals.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

RENT
Includes equipment rental. For different rental periods, please consult.

Infusion pump of volumetric type with peristaltic perfusion system that accepts universal type set. Comprehensive and effective solution to optimize infusion therapy in all the units of the Hospitals and Health Centers.

• Great quality. Easy to use. Menu in Spanish.
• It has a simple system to calibrate different sets of infusion and can be recorded up to 9 calibrations for different sets.
• It has a horizontal structure with an effective prevention against the entry of liquids. It can be hung from the serum support or placed on a table or car.
• High accuracy, due to an intelligent pulsating compensation made by a double micro-processed unit, resulting in a constant flow of high precision infusion.
• It has five types of infusion mode: Speed ​​mode, Drip mode, Body Weight mode, Time mode and Drug mode.
• Contains drip sensor.
• Contains ultrasonic bubble sensor, high sensitivity.
• It contains a pressure sensor that allows adjustment of 3 levels of occlusion pressure.
• High definition screen, allows the on-screen display of the controlled / running function.
• Illuminated alarm panel (up to 12 alarms). Interface for nurse call.
• Record of 1500 historical events.
• The following features and functions contribute to make the patient's treatment more pleasant:
• Preheating function of the infused solution, with constant temperature of the solution.
• When the pump door is opened, in a dark environment, a light is switched on automatically that allows changing the set or working on the infusion pump without turning on the ambient light.
• Silent operation and without vibrations, because it is equipped with a high quality motor.
• External DC power supply input, also works with 12 VDC input.
• Easy to transport due to its small size and weight (2.5 kg).

TECHNICAL SPECIFICATIONS
Specification of IV set: 20 drops / ml or 60 drops / ml.

Infusion flow rate:
•Set IV of 20 drops / ml:
0.1ml / h ~ 1500ml / h.
1 drops / min ~ 350 drops / min.
• Set IV of 60 drops / ml:
0.1ml / h ~ 200ml / h.
1 drops / min ~ 200 drops / min.
• When the speed is between 0.1ml / h ~ 99.9ml / h, the infusion flow rate is changed from 0.1ml / h.
• When the speed is above 100ml / h, the infusion flow rate is changed from 1ml / h.
• Accuracy: ± 5%.

Bubble Detector:
• Ultrasonic detection method: bubbles are detected above 25μl.

- Occlusion warning speed:
It can be divided into three ranges as indicated,
- High (H) 900mmHg ± 200mmHg (120kPa ± 26,7kPa).
- Central (C) 500mmHg ± 100mmHg (66,7kPa ± 13,3kPa).
- Low (L) 100mmHg ± 50mmHg (13.3kPa ± 6,6kPa).
• Flow rate of the Purge Bolus:
Adjustable between 600ml / h ~ 1000ml / h.
• Kvo rate (to maintain permeable route):
Adjustable minimum flow between 0.1ml / h ~ 5ml / h.

Built-in battery:
• Ni-Mh, 12 Vdc, 2300 mAh, the recharge cycle can be repeated up to 500 times.
• Operating time of the battery: with the battery fully charged, it can run continuously for more than 5 hours at a speed of 25ml / h.

Operation mode:
Keep going.

Protection against the ingress of liquids: IPX4 - Protected against splashing water in any direction.

Historical records:
You can store the historical records of more than 1500 infusions made.

Communication link: SN-1500H: RS-232.

• Supply voltage: 110V ~ to 230V ~ - 50Hz or 60Hz or 12Vcc-5A external.
• Maximum power: 40 VA.
• Classification: class I and internally powered.
• Protection against electric shocks: Type CF.

WORK ENVIRONMENT:
Operating conditions:
• Ambient temperature: + 5ºC to + 40ºC.
• Relative humidity: 20% to 90%.
• Atmospheric pressure: 645mmHg (86kPa) to 795mmHg (106kPa).
Storage conditions:
• Ambient temperature: -5ºC to + 55ºC.
• Relative humidity: 0% to 95%.
• Environmental pressure: 500mmHg (66,7kPa) to 797mmHg (106,3kPa).

ACCESSORIES INCLUDED
1 Power cable to line.
1 user manual.

CERTIFICATES
• Certified Quality Standard:
ISO13485.
Disp. A.N.M.A.T. 3266/2013: B.P.F.
Disp. A.N.M.A.T. 2319/02.
• Safety rules:
IEC 60601-1 (Eq IRAM 4220-1 and IEC 601-1- Req.
IEC 60601-1-2 (Electromagnetic Compatibility).
IEC 60601-2-24 (Infusion Pumps).

FREQUENT QUESTIONS
Do you use any brand of infusion set?
Yes, the pump is not dependent on any brand of supplies. It is recommended that the silicone IV Set be used.

Can it be used on animals?
Yes, it can be used on animals.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

RENT
Includes equipment rental. For different rental periods, please consult.

Syringe infusion pump model SN-50C66T is a constant volume, channel and speed controlled infusion pump. It is characterized by high precision, stable flow rate and low dosage.

It is used particularly for the infusion of sodium nitroprusside, dopamine, propofol and antibiotics for acute and serious illnesses. The pump has multiple types of alarm functions to ensure a safe and reliable infusion process.

This product is used to clinically control the flow and velocity of fluids (drugs, nutrients, and blood) infused into the patient's body for safer use.

GENERAL CHARACTERISTICS
* The equipment can store customized syringe information from 33 different manufacturers, Weigao and 32 other manufacturers, configurable by the user.
* SN-50C66T pump can use sterile and disposable syringes of 5ml, 10ml, 20ml, 30ml or 50ml. Automatically recognizes the syringe in place.
* The equipment can store up to 2000 historical infusion records, which include the following information: injection mode, injection rate, alarm information, total volume injected, threshold value of the occlusion pressure limit of the path, limiting quantity, number of syringe and information of the operation.
* It has the following alarm functions:
Incorrect position of the syringe.
Residual limit.
Occlusion.
End of injection.
No operation.
From empty syringe.
Flow limit exceeded.
Plunger decoupled.
Power cord disconnected.
Discharged battery.
Dead battery.
System error.
* Battery operating time: starting from a full charge, the battery can support 6 hours of operation on one channel at a rate of 5 ml / h.
* Allows operation and battery charging from the car's 12Vdc connector.
* Intended User: Adult, Pediatric, Neonatal

TECHNICAL SPECIFICATIONS
* Dimensions:
306mm x 140mm x 146mm (Length x Width x Height)
* Weight: 2.25kg (includes support).
* Electrical feeding:
AC input: 100V to 240V, 50/60 Hz.
DC input: 12Vdc.
Battery voltage: 12Vdc.
Nominal power: 40 VA.

CERTIFICATES:
* Quality standards:
ISO13485
Disp. A.N.M.A.T. 3266/2013: B.P.F.
Disp. A.N.M.A.T. 2319/02
* Safety rules:
UNE-EN 60601-1. (Eq. IRAM 4220-1 and IEC 601-1), Class I - Prot. Desc. Elect .: CF
UNE-EN 60601-1-2 (Electromagnetic Compatibility).
Authorized by the A.N.M.A.T .: PM 1125-18.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Includes equipment rental. For different rental periods, please consult.

IMPORTANT:The equipment must return in good condition or with wear and tear according to the normal use of the equipment. For the realization of this service, the delivery of a check or promissory note for the value of the equipment will be requested as a guarantee or ask for some other way of guaranteeing.

· It is intended to be used in Dental Implants, in all its stages, and in all types of patients.
· This equipment has been design following international standards, in terms of perfomances and functions.
· High quality motor and great torque, free of vibrations.
· By using a key, you can access the maximum torque selection applied to the tool, between 5 and 45 N cm, or disabled.
· Its adjustable electronic torque meter differentiates it from other equipment.
· Both speed and torque are relative to the selected Reduction. Handpiece reduction: 16:1, 20:1 and 32:1, and digital speed selection, displayed on the display.

MULTIFUNCTION FOOT CONTROL

· Hands-free device for control and programs.
· Heavy multifunction foot control for high stability.
· Main control: It starts the motor in progressive mode (linear) mode or it can be programmed to operate as on/off mode.
· Function: When pressed once, it alternates from one to the other. While holding down, navigate between the three programs of each function.
· Turn: The micro motor tool has the possibility of inverting its rotation, using the DIRECT/REVERSE button on the keyboard, or "Turn" in the multifunction foot control.
· The reverse direction of rotation is indicated on the screen and by an audible tone.
· Pump: Press once, it will turn ON or OFF, when turns ON recalls the last flow rate. Keeping pressed, increase the flow; Off, On 25, On 50, On 75, On 100, Off. This is being represented on the display with 1, 2, 3, or 4 drops.

PERISTALTIC PUMP

Is located in the back of the equipment. Supply 15 ml/min to 45 ml/min for jobs that require it.

CONTENTS

- 1 Main Unit Control.
- 1 Main Power Cable.
- 1 Multifunction Foot Control.
- 1 Brushless Micromotor.
- 1 Sterilisable Headpiece Holder.
- 3 Set Irrigation Tubes.
- 1 User's Manual.
(Handpieces are not included).

TECHNICAL SPECIFICATIONS

Unit Control:
- Global Size: 270mm x 115mm x 230mm.
- Power Input: 90Vac-240Vac 50/60Hz (Automatic).
- Line Fuse: 2.5A/250V, 5mm x 20mm SB.
- Nominal Power: 3W.
- Maximum Power: 150W.
- Screen: LCD - 5.5" (High Luminosity).
- Weight: 2Kg.

Pump:
- Type: Peristaltic with 3 rollers.
- Flow: 15-45ml/min including off.

Multifunction Foot Control:
- Global Size: 18mm x 13.5mm x 43mm.
- Weight: 1.65Kg.
- Protection grade: IPX4.

Motor:
- Rate: 500rpm, 50000 max.
-Torque: 5 to 45 N.cm.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.

Includes equipment rental. For different rental periods, please consult

Feas Electrónica MULTIPAR LCD Patient Monitor is designed for monitoring the vital signs of patients in Intensive Therapies, Coronary Units, Operating Rooms, Emergency Rooms, and in a wide variety of clinical-hospital environments, where several vital signs need to be monitored of a patient simultaneously.

GENERAL CHARACTERISTICS
FUNCTIONS:
• Menu, messages and instructions in English.
• Single sweep speeds for circulatory and respiratory system: 12.5, 25 and 50 mm/s.
• Visual and audible QRS indicator proceeding from ECG or Oxymeter.
• When QRS proceeds from the Oxymeter, the sound changes its tone as SpO2 modifies.
• Three alarm levels: physiologicals, technicals and generals.
• Upper and lower limits adjustable by the user.
• Visual and audible alarm indicators, on screen and on top of the equipment.
• Hotkey to activate the silent alarms for 2 minutes.
• Alarms Turn Off.
• User friendly menu by using the selector knob and hotkeys.
• Waveform print-out on standard printer.
• Analog outputs for ECG, RESP, IBP and a synchronization pulse.
• Networking Connection for Centralized Monitoring.
• WAIT Mode: stops monitoring, which allows changing to another patient without activating the alarms.
• Screen menu: normal, 7 leads of ECG, Tabular trends or graphical trends, frozen and measuring of calipers, large numbers.

BASIC CHANNELS
ELECTROCARDIOGRAM
• Heart rate: 20 to 300 1/min.
• Gain selection: 1/4, 1/2, 1, 2 and 4 cm/mV, individual or for both channels.
Visual and audible QRS indication.
Automatic selection of 3 or 5 leads patient cable.
• 3 leads with 3 wire patient cable. Lead selection: DI, DII or DIII.
12 leads with 5 wire patient cable. Lead selection: DI, DII, DIII, aVR, aVL, aVF and C1, C2, C3, C4, C5 or C6.
50Hz or 60Hz Notch filter and Diagnostic, Monitoring or Surgery filter.
• Heart rate alarms, minimum and maximum: 20 to 300 1/min and off.
Lead off detection.
Pacemaker pulse detection.
• Pacemaker pulse rejection in counting the heart rate:
•Pulse rejected characteristic:
- Amplitude: from ±2 mV to ±700 mV
- pulse width: from 0.1 ms to 2.0 ms.

ANALYSIS AND CLASSIFICATION OF ARRHYTHMIAS
• Detects and classifies the following arrhythmias: PVC, PAC, PNC, Bigeminy, Trigeminy, Couple, Run, Tachycardia, Bradycardia, VT, VF and Asystole.
• Store up to 32 events and allows review and printing.
• Measurement of the S-T segment: both the isoelectric point and the ST point are user adjustable (J-point +60 ms or +80 ms, or any other value in ms, from 1 to 120 ms).
• Range: ±2.00 mV.

OXYGEN SATURATION
Plethysmographic waveform, display of oxygen saturation (SpO2).
Measurement signal low perfusion and motion.
• SpO2:
- Range: 35% to 100%
- Precision:
±2% from 80% to 100%.
±3% from 70% to 79%.
- Resolution: 1%.
- Alarm: 0% to 100% and off.
- Initial alarm: 85%.
• Pulse rate:
- Range: 25 to 250 1/min.
- Precision: ±2 1/min.
- Resolution: 1 1/min.
- Alarm: 20 to 300 1/min and off.
Waveform gain adjustment x1/2, x1 and x2.

Accessories included:
Finger pulse oximeter sensor.

RESPIRATORY WAVEFORM
Impedanciometric method.
• Measurement selection: Transabdominal or Transtoraxic.
• Respiratory rate: 5 to 170 1/min.
Apnea Alarm.
• Respiratory rate alarm, minimum and maximum: 5 to 170 1/min and off.

NON-INVASIVE BLOOD PRESSURE (NIBP)
Oscilometric method.
• Use: ADULT or NEONATE.
• Measurement mode: AUTOMATIC or MANUAL.
• Measure unit: mmHg.
• Resolution:
- Pressure: 1 mmHg.
- Pulse rate: 1 1/min.
• Transductor accuracy: ±3 mmHg.
• Ranges:
- PEDIATRIC/ADULT
Systolic pressure: 25 to 265 mmHg.
Diastolic pressure: 12 to 220 mmHg.
Mean pressure: 18 to 245 mmHg.
Pulse rate: 40 to 240 1/min.
- NEONATE
Systolic pressure: 25 to 135 mmHg.
Diastolic pressure: 12 to 110 mmHg.
Mean pressure: 18 to 120 mmHg.
Pulse rate: 40 to 240 1/min.
• Alarm limits of:
- Systolic pressure from 20 to 255 mmHg and off.
- Diastolic pressure from 5 to 220 mmHg and off.
Display of the last 1440 measurements (48 hours, every 2 minutes).
Print-out of the measurements in table form.
Manual or automatic start of the measurement at programmable intervals of 2, 3, 4, 5, 10, 15, 30, 60 and 90 minutes.
• Protections:Double protection from over-pressure.
- Over-pressure of 300 mmHg + 20 mmHg for the Adult mode.
- Over-pressure of 150 mmHg + 15 mmHg for the Neonate mode.
- Protection for exceeding time of measurement.

Accessories included:
Cuff for Non Invasive Blood Pressure.
Hose for Non Invasive Blood Pressure.


INVASIVE BLOOD PRESSURE (IBP) (OPTIONAL)
1 or 2 channels of invasive blood pressure, according to customer's choice.
Simultaneous measurement of Systolic, Diastolic and Mean pressure.
• Range: -30 to 300 mmHg.
• Mode selection for Pressure Ranges: Automatic or Manual.
• Mean Pressure alarm: minimum and maximum limits from -30 to 300 mmHg and off.
• Label: ART, AoP, LVP, PAP, CVP, WDG, RAP, RVP, ICP, IAP and IEP.
• Measure unit: mmHg.
CVP, ICP, IAP and IEP can measure in mmHg or cmH20.

TEMPERATURE (OPTIONAL)
2 channels of temperature.
Compatible with Thermistor Series YSI 400.
Measurement of body temperature or injectate temperature during measurement of Cardiac Output, from -5ºC to 45ºC.
• Resolution: 0.1ºC.
• Accuracy: ±0.2ºC.
• Temperature Alarm, minimum and maximum: -5ºC to 45ºC and off.

Accessories included:
Feas Electrónica temperature sensor - DB9M / G.
Derivation box for Temperature 1 and Temperature 2 parameters, DB9M connector (for two Temperature channels).

CARDIAC OUTPUT (OPTIONAL)
• Entry of patient parameters: Weight, height.
• Selection of:
- Injection volume: 3, 5 and 10 ml.
- Catheter Constant K or Computing Constant (CC)
- Measurement of the temperature in blood and injected.
• Calculation of:
- Body surface.
- CO: Volume in liters / min.
- SV: Stroke volume.
- CI: Cardiac index.
- SI: Systolic index.
Waveform graph for blood temperature as a function of time.
Manual or automatic start of the measurement when injecting.

Accessories included:
Catheter adapter cable for cardiac output - DB9M/G
Derivation box for parameters Temperature 1 and Cardiac Output with DB9.
Derivative box for parameters Temperature 1, Temperature 2 and Cardiac Output with DB9.

SIDESTREAM CAPNOGRAPHY (OPTIONAL)
Measurement of EtCO2, FiCO2 and Respiratory Rate.
• Range:
- CO2, from 0 to 100 mmHg (0% to 13%).
- Respiratory Rate, 4 to 170 1 / min.
• Accuracy:
- CO2, ± 2 mmHg for CO2 <5%.
- <10% of reading for CO2> 5%.
• Resolution:
- CO2, 1 mmHg.
- Respiratory Rate, 1 1 / min.
• Alarm:
- FiCO2, EtCO2, minimum and maximum, 0 to 100 mmHg and off.
- Minimum and maximum Respiratory Rate, 0 to 170 1 / min and off.
Calibration: 2 zero points (ambient air) and gain (5% or 10%).
Compensation for temperature and atmospheric pressure, O2 and N2O.

Accessories included:
Type "T" nozzle for Feás Electrónica lateral flow capnography.
2.4 m patient line for Feás Electrónica lateral flow capnography
Moisture filter for lateral flow capnography, Feas Electrónica

SIDESTREAM CAPNOGRAPHY WITH ANESTHETIC GASES MEASUREMENT (OPTIONAL)
Measurement of EtCO2, FiCO2 and Respiratory Rate.
• Range:
- CO2, from 0 to 100 mmHg (0% to 13%).
- Respiratory Rate, 4 to 150 1/min.
• Accuracy: CO2, ±3%ABS.
• Resolution: CO2, 1 mmHg.
- Respiratory Rate, 1 1/min.
• Alarm: FiCO2, EtCO2 minimum and maximum, 0 to 100 mmHg and off.
• Respiratory Rate minimum and maximum, 0 to 150 1/min and off.
• Measurement of N2 O: from 0% to 100%.
•Automatic detection and measurement of up two anesthetic gases: Halothane, Enflurane,Isoflurane, Sevoflurane and Desflurane.
- Range: 0% to 30%.
- Accuracy: ±8%REL.
- Resolution: 0.1%.
Flowrate:
- 70 to 120 ml/min for neonatal patients.
- 120 to 250 ml/min for adult patients.

Accessories included:
"T" type nozzle for sidestream Capnography, Feas Electrónica.
2,4 m patient line for sidestream Capnography, Feas Electrónica
Water trap for use in lateral flow capnography and anesthetic gases.

MAINSTREAM CAPNOGRAPHY (OPTIONAL)
Measurement of EtCO2, FiCO2 and Respiratory Rate.
• Range:
- CO2, from 0 to 100 mmHg (0% to 13%).
- Respiratory Rate, 4 to 150 1 / min.
• Accuracy: ± 2 mmHg between 0 and 40 mmHg and ± 5% of reading 41 and 70 mmHg.
• Resolution: 1 mmHg.
• Calibration: only zero (ambient air).
Compensation for temperature and atmospheric pressure, O2 and N2O.
Warm-up time <15s, to start measuring, within 2 minutes and obtain measurement values according to specifications.
• Waveform response time: less than 60 ms.

Accessories included:
Mainstream Capnography sensor, Feas Electrónica
Nozzle for mainstream Capnography sensor

FiO2 (OPTIONAL)
Fraction of inspired Oxygen: from 0% to 100%.
Polarographic cell measurement principle.
Alarms minimum and maximum: 0% to 100% and off.

Accessories included:
Derivative box for pressure 1, pressure 2 and / or FiO2 parameters with DB9M.
FiO2 Sensor, Feas Electrónica.
Disposable Oxygen Sensor T-adapter for FiO2, Feas Electrónica
Spiral cable of Oxygen Sensor for FiO2, Feas Electrónica.

ANY OTHER OPTIONAL CHANNEL SPECIFIED CAN BE ADDED IN THE FUTURE.

TECHNICHAL SPECIFICATIONS
15” LCD-TFT Color Monitor
• Resolution: 1024x768.
Wide angle of visibility.
• Dimensions:
- Height: 345mm; Width: 335mm; Depth: 205mm.
• Weight: 6Kg.
• Power Supply: 90V~ to 240V~ (with automatic voltage selection) 50Hz or 60Hz.
• Power Consumption: 85VA.

CERTIFICATIONS
• Quality Standard (Certificates):
- ISO 13485.
- Disp. A.N.M.A.T. 3266/2013: B.P.F.
- Disp. A.N.M.A.T. 2319/02.

• Safety Standard (Certificates):
- UNE-EN60601-1.(Eq. IRAM 4220-1 and IEC 601-1).
- Electrical-shock protection: Class I – CF.
- UNE-EN60601-1-2 (Electromagnetic compatibility).
Authorized by A.N.M.A.T.: PM 1125-2.

ACCESSORIES
Included:3 or 5 leads patient cable.
Disposable electrodes.
SpO2 sensor.
SpO2 extension cable.
Cuff for NIBP.
Silicone hose for NIBP.
Temperature sensor Feas Electrónica - DB9M/G.
Derivation box for parameters of Temperature 1 and Temperature 2, DB9M connector.
FiO2 Sensor Feas Electrónica.
T Adapter for FiO2 sensor Feas Electrónica.
Spiral cable for FiO2 sensor Feas Electrónica.
Power cord.
User manual.
The image is illustrative.

The images shown are for illustrative purposes only and may differ from the actual product. Specifications are subject to change without notice.